Hallo zusammen,
Ich habe einen alten dvb-t Klassiker unter gentoo installiert, eine Twinhan Magicbox, alles sieht gut aus, nur er findet keine Signale, unter Windoof jedoch einwandfrei
Hier ein auzug aus dmesg
dvb-usb: TwinhanDTV USB-Ter USB1.1 / Magic Box I / HAMA USB1.1 DVB-T device successfully deinitialized and disconnected.
dvb-usb: found a 'TwinhanDTV USB-Ter USB1.1 / Magic Box I / HAMA USB1.1 DVB-T device' in cold state, will try to load a firmware
dvb-usb: downloading firmware from file 'dvb-usb-dibusb-5.0.0.11.fw'
dvb-usb: generic DVB-USB module successfully deinitialized and disconnected.
dvb-usb: found a 'TwinhanDTV USB-Ter USB1.1 / Magic Box I / HAMA USB1.1 DVB-T device' in warm state.
dvb-usb: will use the device's hardware PID filter (table count: 16).
DVB: registering new adapter (TwinhanDTV USB-Ter USB1.1 / Magic Box I / HAMA USB1.1 DVB-T device).
DVB: registering frontend 0 (DiBcom 3000M-B DVB-T)...
input: IR-receiver inside an USB DVB receiver as /class/input/input3
dvb-usb: schedule remote query interval to 150 msecs.
dvb-usb: TwinhanDTV USB-Ter USB1.1 / Magic Box I / HAMA USB1.1 DVB-T device successfully initialized and connected.
localhost linux # lsmod | grep dvb
dvb_usb_dibusb_mb 10624 0
dvb_usb_dibusb_common 5508 1 dvb_usb_dibusb_mb
dvb_usb 16712 2 dvb_usb_dibusb_mb,dvb_usb_dibusb_common
dvb_core 61672 1 dvb_usb
firmware_class 6528 1 dvb_usb
dvb_pll 11524 3 dvb_usb_dibusb_mb,dvb_usb_dibusb_common,dvb_usb
dib3000mc 11520 1 dvb_usb_dibusb_common
dib3000mb 9408 1 dvb_usb_dibusb_mb
usbcore 91332 8 dvb_usb_dibusb_mb,dvb_usb,ohci_hcd,hci_usb,usblp,ehci_hcd,uhci_hcd
i2c_core 16016 7 dvb_usb_dibusb_mb,dvb_usb,dvb_pll,dib3000_common,radeonfb,i2c_algo_bit,i2c_viapro
tzap -c /usr/share/dvb/zap/dvb-t/de-Ruhrgebiet "SUEDWEST RP-59"
using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
reading channels from file '/usr/share/dvb/zap/dvb-t/de-Ruhrgebiet'
tuning to 778000000 Hz
video pid 0x1441, audio pid 0x1442
status 00 | signal 0000 | snr 0000 | ber 001fffff | unc 0000ffff |
status 04 | signal 0000 | snr 0000 | ber 001fffff | unc 0000ffff |
status 04 | signal 0000 | snr 0000 | ber 001fffff | unc 0000ffff |
status 04 | signal 0000 | snr 0000 | ber 001fffff | unc 0000ffff |
status 04 | signal 0000 | snr 0000 | ber 001fffff | unc 0000ffff |
wie man sieht signalstaerke 0, status 4, sollte eigentlich 1f sein
dvbscan / w_scan findet auch keine signale
irgend jemand noch eine Idee?????
gruss